User Tag List

Thanks Thanks:  0
Likes Likes:  0
Page 1 of 2 12 LastLast
Results 1 to 10 of 14

Thread: Trim Removal

  1. #1
    Regular Member
    Join Date
    Jul 2005
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Vehicle InfoStats





    Default Trim Removal

    I need to fit a handsfree kit.

    Does anybody know how to remove the A-pillar trim so that I can run the microphone lead? It looks like the curtain airbag might be anchored at the bottom of the A-pillar.

    Thanks

  2. #2
    Regular Member C19_CJB's Avatar
    Join Date
    Jun 2005
    Location
    Beverley, East Yorkshire
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Vehicle InfoStats





    Default

    I didn't dare take that trim off just incase I set the airbag off!!

    I ran my wire down the steering column and mounted the mic on the pad between the cluster and the steering wheel

  3. #3
    Regular Member vectra 2.0 t's Avatar
    Join Date
    Jun 2005
    Location
    tasmania
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Vehicle InfoStats





    Default

    give leeds vectra a pm hes your man

  4. #4
    Professional Trader
    Join Date
    Jun 2005
    Location
    sheffield
    Post Thanks / Like
    Mentioned
    1 Post(s)
    Tagged
    0 Thread(s)
    Vehicle InfoStats





    Default

    Just pull the a-piller trim off, its only clipped in, its not attached to the air bag at all..

  5. #5
    Ex Vec-C Admin / Founder Duncan's Avatar
    Join Date
    Jun 2005
    Location
    East Sussex
    Post Thanks / Like
    Mentioned
    1 Post(s)
    Tagged
    0 Thread(s)
    Vehicle InfoStats





    Default

    As Rich says, it just pulls off. You won't set off any airbags.

    This PDF should help you as well. You may damage a couple of clips when taking it off, these can be easily obtained from Vx.

    HTH

    D

  6. #6
    Regular Member leeds vectra's Avatar
    Join Date
    Jun 2005
    Location
    Leeds
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Vehicle InfoStats

    Vehicle : Insignia

    Trim : VX-Line

    Engine : BiTurbo

    Year : 2014

    Default

    You all beat me to it. As above

    PAul.

  7. #7
    Regular Member
    Join Date
    Jul 2005
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Vehicle InfoStats





    Default

    Fantastic. Thanks.

  8. #8
    Regular Member
    Join Date
    Jun 2005
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Vehicle InfoStats





    Default

    All I do is get my fingers under edge and pull a little then took wire behind with screw driver I have done this with last 3 cars and not taken trim off and you couldn't see any wires

  9. #9
    Regular Member
    Join Date
    Jul 2005
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Vehicle InfoStats





    Default

    I've just been scoping out the install.

    I've pulled as hard as I dare, but I can't for the life of me get the A pillar trim off. The flat plastic clip that goes through the trim at the top just won't budge. I could just tuck the cable in between the trim and the door rubber as suggested above, but this would place the wire between me and the airbag. I'll see if I can tuck it in between the windscreen and the trim instead.

    I've also had the radio (CD30) out. Vx have conveniently labelled the pins, and there's even a (mono) audio input. I'm not a fan of Scotchlok connectors so I'll probably just get an aftermarket cable adaptor but there's no ignition switched supply to the radio.

    I dismantled the trim around the cigarette lighter to see if I could tap in there and I noticed that there's a unused wire taped to cigarette lighter connector. Anybody know what that might be?

  10. #10
    Ex Vec-C Admin & Founder Bainie's Avatar
    Join Date
    Jun 2005
    Location
    60 Degrees North !!
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Vehicle InfoStats





    Default

    Is it safe to put a wire in front of an airbag ? will it not prevent the airbag functioning properly ?

Page 1 of 2 12 LastLast

Thread Information

Users Browsing this Thread

There are currently 2 users browsing this thread. (0 members and 2 guests)

Similar Threads

  1. A-Pillar trim removal
    By jammy_c in forum Electrical & ICE (including SatNav)
    Replies: 1
    Last Post: 11th September 2012, 15:26
  2. Help! Hatch Trim Removal
    By wafoo in forum Bodywork & Interior
    Replies: 4
    Last Post: 16th February 2012, 18:28
  3. Pedal Trim Removal
    By vectrasimonsri in forum Bodywork & Interior
    Replies: 3
    Last Post: 6th April 2011, 10:42
  4. Dash trim removal - Please help
    By AntSSSS in forum Vectra C / Signum Car Chat
    Replies: 2
    Last Post: 10th March 2009, 12:57
  5. Trim removal
    By Big Sig in forum Vectra C / Signum Car Chat
    Replies: 2
    Last Post: 9th February 2007, 14:45

Visitors found this page by searching for:

Nobody landed on this page from a search engine, yet!

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •